The Official Superchips Forum

My car is 2009 xterra manual transmission and I just purchased my Flashpaq tuner and when I connect it to the car with the ignition on it reads the car saved file until 100% and then it says “Vehicle calibration not on file” , and when I clicked on the vehicle identification it says
VIN:NA
Vehicle file : 1ZL83A

I tried to update the tuner and it updated successfully with the information below
Serial 000001473404
Version 01.05.07
Gas truck DB 150

However car is a gulf specs , and my car's VIN code is “ 5N1AN0N64AC510320.
Your kind support is highly appreciated .

Thanks & regards

Welcome to Superchip's Forum!!

Ahmed, I am having the engineers take a look at this one, this will take a few days.
Issue Tracking: ID = 100484




Ron

_________________
RRAPP@SUPERCHIPS.COM
1-888-227-2447
8-5 EST.

Email me directly if your having ANY trouble with the forum.
Not able to LOGIN, email me with your Username that you registered with.

Hi Ron ,

any news ?

regards

hi Ron ,

Its been more than two weeks for this issue , and i haven't got any updates ? pls tell me the status .

regards

"Have him attempt stock read again and find out if it takes 5 minutes or 45 minutes..."

Also


"make sure customers PC language is set english US. if it isnt then change it and update for stockread"

Ron

_________________
RRAPP@SUPERCHIPS.COM
1-888-227-2447
8-5 EST.

Email me directly if your having ANY trouble with the forum.
Not able to LOGIN, email me with your Username that you registered with.

Every time when i try it takes 45mins beside my pc language is set to English , your help pls .

thanks

I will let them know.

Ron

_________________
RRAPP@SUPERCHIPS.COM
1-888-227-2447
8-5 EST.

Email me directly if your having ANY trouble with the forum.
Not able to LOGIN, email me with your Username that you registered with.

Hi Ron ,

Any news .

Verify he gets gas truck db 157, then attempt read stock, if it takes the 45mins still. Let me know.
Ron

_________________
RRAPP@SUPERCHIPS.COM
1-888-227-2447
8-5 EST.

Email me directly if your having ANY trouble with the forum.
Not able to LOGIN, email me with your Username that you registered with.

Hi Ron,

Just updated the programmer and got
Serial 000001473404
Version 01.05.08
Gas truck DB 168
And now it no longer takes 45minutes,
After that it took about 3 minutes to read and save stock file and then it says “Vehicle calibration not on file“
Then it says please use internet to update your programmer (code # E-6D)
After that I connected it again for internet update it took a while to send the car file and then the below message appears

Hi Ron ,

Just got an e-mail for updating my programmer and i did , i just updated it and it went perfectly on the car , and had to tune on 93 performance and the car was great .

Thanks so much for your help and support , i appreciate your effort .

Regards

Ahmed

hello Ron ,

I am very happy with the overall results of performance , however i found that the speed limiter still the same so if possible to remove my speed limiter please .

The other thing when i went to increase the timing advance in advanced options i got a message that the car has not reached the operating temperature although i tried it several times after driving a long time and even while the car is in cold condition . i need your support on how can i advance the timing pls .

Thanks & regards

I will send this over to the engineers.


Ron

_________________
RRAPP@SUPERCHIPS.COM
1-888-227-2447
8-5 EST.

Email me directly if your having ANY trouble with the forum.
Not able to LOGIN, email me with your Username that you registered with.

Robert has sent me an e-mail and yes the timing advance should be done while the car is running and it works , now with 3 more timing advance the car has a very aggressive response through the entire rpm .

still waiting for the speed limiter removal as they are working on it .

Thanks man .

regards